VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Vape Coil  /  Sourcing Vape Coil: contract and PO terms primer
vape coils · first-time buyers

Sourcing Vape Coil: contract and PO terms primer

We ship vape coils to distributors, chain buyers and independent shops. What follows is the material we normally cover in a first conversation: what we hold in stock, how we test it, how it ships, and what happens when a carton arrives damaged.

Published 27 November 2025  ·  VapeWholesaleHub  ·  Reading time 8 min

Sourcing Vape Coil configuration from a production run, photographed before packing.
Sourcing Vape Coil configuration from a production run, photographed before packing.
Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Packaging proof for the export market, approved before the run.
Packaging proof for the export market, approved before the run.

Choosing the core line

Vape Coil is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Most first-time buyers arrive with a spreadsheet and leave with too many SKUs. The fix is not a bigger catalogue, it is a narrower core. We normally propose three tiers: a volume line that carries the shelf, a step-up line that lifts basket value, and one trial SKU that tells you what to order next season.

We keep a short list of approved configurations for vape coils. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.

Where defects actually come from

14 separate checks run before a carton is sealed: electrical, mechanical, leak, finish and packaging. Anything outside tolerance is quarantined the same day and reported to you, rather than shipped with a hope and a discount.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

For first-time buyers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Unit price versus landed cost

Unit price breaks usually land at 300, 800 and 1600 pieces. Between those steps the cost curve flattens, which is why pushing a 200 unit order to 500 often costs less per unit than buyers expect.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

  • Document pack prepared per destination market
  • Cartons drop-tested and pallet-counted for clean freight
  • Seven-day defect reporting with replace-or-credit
  • Standing reorder schedule with a fixed cut-off
  • Batch codes traceable from carton back to production date
  • Artwork proof plus physical dummy for custom packaging

Compliance without the last-minute scramble

Age verification is not only a website problem. Retail packaging, shelf placement and staff scripting all carry compliance weight, and auditors increasingly ask for evidence of all three.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Specification summary

Typical specification for this category
Resistance0.60 ohm
BuildClapton
WickingCotton bacon
FitmentPress-fit
Pack size5 per pack
CompatibilityUniversal deck
Minimum order300 units per SKU, mixed cartons allowed
Lead time12 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

What is the minimum order for vape coil?

Standard configurations start at 300 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 800 units because of setup time on the line.

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 300 units. We would rather you handle the sample than approve a specification from a photograph.

Related reading

Need a quotation on vape coils?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on vape coils

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us